Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
What are your thoughts with regards to How to Install a Bathtub Yourself?
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably hard job. If the old tub is easily obtainable, the job can move easily; if you need to open a wall surface to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the job as well as fit trying it. As opposed to hiring a professional to take control of a halfway-completed job, it is far better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly aid you set up a brand-new bath tub in your washroom if you have already gotten a new tub and don't need to change the plan of your previous water supply pipes.
Your devices and also product list need to consist of the following:
Getting ready for the Installation
First of all, the sustaining frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the limited access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bathtub in the called for placement. The wood boards are handy in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the supply of water as well as check all joints and new pipework for leakages and also tighten them if essential. Load the bathtub as well as likewise examine the overflow electrical outlet and also the typical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been used at the very least when as this will certainly settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in area between the tap and the sink. Safeguard the tap in place with the manufacturer offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a stiff seal, causing the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very eager about How to Install a Bathtub Yourself and I am hoping you enjoyed the new blog post. Liked our article? Please share it. Let others locate it. I cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Efficient, reliable plumbing services here. Report this page